dcsimg
A Flash Developer Resource Site

Results 1 to 2 of 2

Thread: I want an actual size FLV of my MPEG.

  1. #1
    Registered User
    Join Date
    Aug 2011
    Posts
    1

    Lightbulb I want an actual size FLV of my MPEG.

    I have converted my MPEG video recorded from my camcorder to FLV to use on "Flash CS4" using "Adobe Media Converter". But the FLV playback on the "Flash player 10" is alot smaller than the playback of the MPEG video on "VLC". Is there anyway to adjust any properties to get the FLV to the actual size of the MPEG video? I hope someone knows what i mean here. Thanks.

  2. #2
    Senior Member
    Join Date
    Sep 2010
    Posts
    324
    The display size and the bitrate are set in the Adobe Media Converter.
    That is where you set the dimensions.
    http://www.adobe.com/devnet/flash/qu...o_encoder.html
    If you are not familiar with bitrate... here's an old article:
    Video bit rate

    One of the principle of goal setting is to "Begin with the end in mind". In this case it'll be very hard to give good recommendations because the end is not defined. So I'll just make a few assumptions and you can correct me as needed.
    First, I'll assume that since you are converting to Flash, you want to deliver this video over the Internet. If that's true, then we'll have to make some assumptions on the Internet connection download speeds of your potential viewers. Let's just say that most have at least a 1.5Mb connection or faster.
    OK, that would mean that a video bitrate of half that should usually provide a video download that is not interupped by buffering (most of the time anyway). So assuming a video bitrate of 750kbps, what would the optimum display dimensions be?
    Before we decide, here's a little info about bitrate. For highest quality playback, the video bitrate is tied directly to the display dimensions. That is, the larger the display, the more incoming data is required to properly display the video. Think of bitrate in terms of a can of paint. If you have 1 quart of paint, you might be able to do a very nice job on a 32 X 24 foot area. But if you try to stretch that same amount of paint out over a 64 X 48 foot area, the coverage will not be nearly as good and you get poor results.
    In the same way, a video displayed at 640 X 480 pixels will require 4 times the bitrate as a video displayed at 320 X 240 pixels to produce the same quality. So for example a video with a bitrate of 100kbps, displayed at 160 X 120 will produce the same quality results as a video with a bitrate of 1600kbps if displayed at 640 X 480.
    So to boil it all down, video bitrates of 750kbps, even up to 1000kbps can usually get delivered of the Internet on most high speed connections. Higher bit rates may work for really fast connections but will cause problems for viewers with slower connections. Video display size has a direct bearing on the final quality. In the 750 to 1000kbps range, display size should be kept around 450 or 500 width max (and whatever height the aspect ratio calls for). Yes it can be displayed larger, but the quality will suffer.
    Sound like your audio settings are fine, especially for Internet delivery.
    As for framerate, maintain the original raw video framerate for best results. So if the video was shot at 24fps, leave it.
    As for video converters, do you have the Flash 8 Video Converter? It works just fine for video to be delivered over the Internet. Remember, you are taking a Cadillac version of video (h.264 HD) and stuffing it into a Chevy body to get it to work over the Internet.
    Best wishes,
    Video Man

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  




Click Here to Expand Forum to Full Width

HTML5 Development Center